Keg Dispensing Supplies

A bonnet angler is a little piece that comes in handy when trying to use an extra-long tap handle on a kegerator that has a flat surface, such as a converted refridgerator. Often, a longer tap handle won't have the clearance necessary, and will hit the body of the kegerator, not able to fully shut the beer faucet. Alleviate these problems with a bonnet angler! The bonnet angler creates a slight forward lean, giving you room to proudly display your long tap handles!

This is a replacement brass faucet lever for standard faucets. It is the brass piece that the faucet knob or handle screws onto, and fits into the plunger assembly. It moves forward and backward, working in tandem with the plunger assembly to allow beer to flow. These brass levers are known to break every once in awhile, so if you need a replacement, we have one for you right here!

Gas lost in your CO2 system can lead to a shorter life span of your CO2 cylinders. Prevent CO2 loss with a washer! A plastic CO2 washer fits between your CO2 cylinder and regulator and helps to create a good seal. A good seal ensures that you don't lose gas when carbonating or serving. These plastic CO2 washers fit Taprite brand regulators, as well as many standard-sized CO2 regulators. Keep a few on hand in case of an emergency!

The secret weapon for keeping a clean brewery! A double ended brush can come in handy for cleaning all those hard-to-reach places, not only in your dispensing system, but also in your brewing equipment. The two ends have two different sizes brushes, which come in handy in cleaning faucet parts, keg posts, dip tubes, racking arms, ball valves, bottle fillers...the list goes on! Keep every nook and cranny of your brewing equipment clean with one of these. Highly recommended to anyone who owns a keg or a permanent dispensing setup.

Superflush Tap & Line Cleaner is an safe, easy-to-use, economical and biodegradable line cleaner perfect for use on kegerators and draft dispensing systems. Simply mix 2-3 oz. with 1 gallon water as per the instructions and pump through lines. Allow to sit in lines for a few minutes, then flush clean with water. A solution made at the same rate may be used to clean faucet and coupler parts as well. Sold in a 32 oz bottle, Superflush can help you keep your lines pristine, pouring perfect beer every time!

Party Pig Pressure Pouch

A swivel nut set with a barb for your gas side connections! These swivel nut sets come with a standard 1/4" female flared nut and a 5/16" barb that can be used with standard 5/16" ID gas tubing. These can be connected directly to the standard liquid disconnects that we offer, or used with a plastic flare fitting for any direct metal-on-metal connections.

This CO2 shutoff with barb and check valve is ideal for use with CO2 regulators and manifolds! It has 1/4" MPT right-hand threading on one side that threads into most standard regulators and manifolds. On the other end is a standard 3/8" barb, which works perfectly with standard CO2 gas line. Get one of these to replace a damaged or missing shutoff, put on a wye splittler, or create your own CO2 apparatus!

Is your tap handle too short? Not visible or prominently displayed, like you would like? Look no further than this chrome extension to solve your tap handle woes! This 1-inch chrome extension is placed between your faucet and tap handle to extend it outwards. Simple to use and effective, get the right length for your tap handle today!

These quick connects come in handy for quickly connecting to and disconnecting from connections of all kinds! This is the female side that has a gray disconnect button for quickly disconnecting from the male end. It has a 1/4" straight barb to hook up to 1/4" ID tubing. It has a temperature tolerance range from -40 to 180F and a vacuum pressure tolerance of 120 PSI. This female piece is used with the 1/4" Quick Connect Insert, item #05P01-122.

Bevlex tubing is a high quality thick-walled tubing. This 3/16" tubing works well for beer line, as it is the standard inner diameter for most serving systems. While the thinner walled tubing may also be used, this thick-walled tubing is recommended for permanent installations, such as on a kegerator or keezer dispensing system. It is also recommended when a thicker wall would come in useful. It is more durable and can withstand more pressure than the thinner-walled version.

Inner Diameter: 3/16 in.
Outer Diameter: 7/16 in.

A black plastic picnic faucet comes in handy in a pinch! Affectionately referred to as a cobra tap, this is a fairly simple dispensing mechanism. When the lever is pressed, the rubber gate is lifted, allowing beer to flow. These picnic faucets come apart easily for cleaning, and feature a barbed end that can fit on standard beer line. Make your own or keep one on hand in case the unthinkable happens!

Rustproof wrench for CO2 nut on regulator. The right wrench, right where you need it, when you need it.

This is a replacement plunger shaft assembly for standard faucets. It joins with the faucet lever and moves back and forth to allow beer to flow from the faucet. If you need a replacement for an old standard faucet, Great Fermentations has one for you!

Replace your missing or damaged coupling nut with one of these replacements from Great Fermentations! These also work well with a faucet adapter (item #17C13-100). Put one of these on the faucet adapter, add a faucet and a liquid disconnect on the other end, and you have yourself a faucet assembly ready to put on a cornelies keg!

Oetiker clamps provide a permanent clamping solution! This style of clamp has a 1-ear design, which means they are crimped at a single point on the clamp to create a superior seal over your tubing. These small Oetiker clamps are often used on 3/16" thin-walled tubing that is used in some liquid applications and on thin-walled liquid draft lines. These clamps hold tight, creating a great seal that holds for a long time! Some people prefer these for more permanent systems. If you are looking to switch over to a snug seal that lasts, make sure you use Oetiker clamps!

German beer lovers rejoice! This "A" style German slider keg coupler, also known as a tap, is just what you need to get beer flowing from German kegs! This coupler is like no other, with a cupped mount that slides onto the keg and locks in place when engaged. This is the most widely used keg coupler in Germany, and while it will not work with all German beer kegs, it does work with most of them, as well as with a few Belgian kegs. Among the breweries that use the "A" coupler are Ayinger, Achouffe, Bitburger, Franziskaner, Hacker-Pschorr, Hoegaarden, Paulaner, Spaten, and Warsteiner. This coupler comes with the gas side connections, but does not include the liquid side connections which consist of a 3/16" liquid tailpiece, a beer nut and a neoprene washer.

The name Perlick has been in the beverage industry for a long time, and has always been associated with high quality draft equipment. The 630SS is no exception. This faucet is forward-sealing so there is less chance of bacterial and yeast activity. A high-quality forward sealing faucet such as this will need to be cleaned less frequently than an inferior back-sealing standard faucet. Being all-stainless, this Perlick faucet is built to last! Staying strong long after other metals begin to degrade, a stainless steel Perlick faucet is something of a long-term investment, but well worth the price!

Do you often carbonate and serve beer at the same time? If so, or if you would like to be able to do both at different pressures, a secondary regulator is perfect for you! Your primary CO2 regulator attaches to your CO2 tank and allows one output pressure. However, a secondary regulator hooks up inline and allows you to regulate to another keg at a lower pressure. This allows you to carbonate one keg at a higher pressure while serving beer from another at a lower pressure! This Taprite secondary regulator is made to the same high standards as all Taprite equipment, with a high quality diaphragm that keeps regulating long after lesser regulators give up the ghost. Regulate at multiple pressures with a secondary regulator from Taprite!

You can never have too many disconnects! For all your pin lock draft needs, Great Fermentations offers you these liquid pin lock disconnects. Easy to take apart and clean, these have their uses not only in picnic taps, jockey boxes and home draft systems, but in a number of other brewing-related projects. These disconnects have a 1/4" MFL connection, which is perfect for attaching a swivel nut set for myriad applications. They have a plastic end on the male flare fitting so you don't have to use a plastic flare fitting washer when connecting them to metal. Make sure you have enough on hand for all the kegging and draft projects your mind can come up with!

This is a black plastic flange, the type that comes with standard beer shanks. It makes your custom kegerator look nice and professional, covering up drilled holes and providing a nice background for your beer faucet. If yours are damaged, replace them with this flange!